Author Topic: Building a cutting table  (Read 693 times)

Petruchio

  • Regular Member
  • **
  • Posts: 49
  • Human Being
Re: Building a cutting table
« Reply #15 on: February 19, 2020, 02:36:59 AM »
Wow, thanks for all the great input. So after reading through the thread I decided to go for plywood as well. I guess the best option then would be an "unfinished" surface?

 I am however painfully aware of the height problem since I am still doing all my cutting on an old dining table and constant back pain while cutting is the main reason I want to build myself a cutting table.


Henry Hall

  • Research
  • Senior Member
  • ****
  • Posts: 660
  • A very small jeff
Re: Building a cutting table
« Reply #16 on: February 19, 2020, 07:03:09 AM »
Put that dining table on blocks while you are building a new table.
‘Being perfectly well-dressed gives one a tranquillity that no religion can bestow.’ - Ralph Waldo Emerson.

Petruchio

  • Regular Member
  • **
  • Posts: 49
  • Human Being
Re: Building a cutting table
« Reply #17 on: June 06, 2020, 08:35:17 PM »
Now, I finally was able to build myself a cutting table from sanded plywood. I was just wondering if there is any finish or treatment I should apply or if I can just leave it as be. It feels a little rough still but nothing too worrisome, I guess.

spookietoo

  • Full Member
  • ***
  • Posts: 128
  • Home Sewist - Focusing on Tailoring TN - U.S.A.
Re: Building a cutting table
« Reply #18 on: June 07, 2020, 09:52:17 AM »
I cut on a hollow core door, 32" w, that hangs on a wall when not in use, and I screw 2 legs in place when needed and balance the other end on a cabinet, giving me access on 3 sides.

I covered the door with a thin layer of poly batting and a flat weave fabric so that the fabric I'm cutting doesn't slip.

I rarely use a rotary cutter.

theresa in tucson

  • Regular Member
  • **
  • Posts: 78
  • Human Being
Re: Building a cutting table
« Reply #19 on: June 07, 2020, 11:20:45 AM »
I use a cheap hollow core door as well, set up on tall saw horses in my garage.  The door is painted (factory finish) so it's quite smooth.  it works quite well.

Schneiderfrei

  • Research
  • Senior Member
  • ****
  • Posts: 827
  • Resembles Human Being
Re: Building a cutting table
« Reply #20 on: June 07, 2020, 12:12:09 PM »
Petrucio, the last thing you want is fine fabric fibres catching on wood grain.

You should varnish it or oil it with linseed.

That would protect the surface from moisture, it would last longer and be smoother.

Sand it down to about 320 or 400 grit - doesn't take a lot of effort at that fine a grit.

The edges are also a consideration.  They should be either rounded slightly or chamfered, again, so that fabric fibres don't catch.

G




pfaff260

  • Full Member
  • ***
  • Posts: 154
  • Human Being
    • http://menfash.us/wp-content/uploads/2013/01/Tailoring-Advice-for-Men-Suits-6.jpg
Re: Building a cutting table
« Reply #21 on: June 07, 2020, 03:31:05 PM »
I started out with such a door as well, but i needed more space, so i topped it with a large sheet of ply wood wich i then painted. Works wonderfull.

Hendrick

  • Full Member
  • ***
  • Posts: 132
  • Human Being
Re: Building a cutting table
« Reply #22 on: June 15, 2020, 06:11:04 AM »

Hi,

I use table tops from laminated oak (you know, made from smal bits) that are inexpensive. I put no finish on them whatsoever, but once a year or so I roll them outside and bleach them with chlorine or peroxide and they look new. I polish them by rubbing the with… a piece of oak; wood on wood...  For cutting, I span a heavy cotton lining over them with lots of clips. For pressing, I do the same, but with two layers of "movers blankets" under the lining.
I have used this setup for some years, works okay for me...

Schneiderfrei

  • Research
  • Senior Member
  • ****
  • Posts: 827
  • Resembles Human Being
Re: Building a cutting table
« Reply #23 on: June 15, 2020, 08:50:19 AM »
That sounds like a labour of love Hendrick. :)