Author Topic: drafting a sleeve  (Read 765 times)

posaune

  • Moderator
  • Senior Member
  • *****
  • Posts: 256
  • Human Being
Re: drafting a sleeve
« Reply #15 on: August 26, 2017, 07:43:21 PM »
the end

Now I show to complete it how to draft a sleeve from the first type of armhole and cap.
A classical slim sleeve with elbow dart  or 2 piece sleeve:
First you draft the front sleeve break, line goes straight down from front notch down. The back sleeve break you find in ½ the distance between C and D. Straight line up and down.


Now the elbow line. You calculate it with 60 % of the Sleeve length , draft down from Point A. Now you tighten the sleeve at elbow . You draft in 1 cm in at front break and back break und at back side seam. You draft 2 -3 cm up at the hem like shown and you mark 1/2 of your hem width from this point to the hem line. You connect like shown in blue for front sleeve and green for back.



you cut down from front notch to hem and cut this part at elbow line. You rotate the front pieces so they touch the blue line. They will overlapp. Now mirrow the blue line at the back break about that line for the formed back sleeve.



You find the point where the front side seam will end. You measure the distance and go to the back side seam and shorten here. Rotate the back and the front so that they will touch at elbow line and back break. Finish with a gentle curved hem. You have to stretch the side seam of front with the iron. To do it easier do notches about up 14 cm from hem and 14 cm down from B and C.
end
I used some books to write this: Maßschnitte und Passform, Guido Hofenbitzer, Verlag Europa Lehrmittel
Schnittkonstruktion für Blusen und Kleider, Deutsche Bekleidungsakademie München, Rundschauverlag,
Pattern Cutting, Dennic Chunman Lo, Laurence King Publishing and my notices from courses held by Schule für Mode und Design, Offenbach.

TTailor

  • Venerable Member
  • Full Member
  • ****
  • Posts: 145
  • There is no formula!
    • A Tailor Made It
Re: drafting a sleeve
« Reply #16 on: August 26, 2017, 11:51:47 PM »
Thanks!
When I get home from vacation I plan on trying them out!

spookietoo

  • Regular Member
  • **
  • Posts: 58
  • Home Sewist - Focusing on Tailoring TN - U.S.A.
Re: drafting a sleeve
« Reply #17 on: August 28, 2017, 03:50:48 AM »
Posaune - Thank you! Thank you! Thankyou!  This is so kind of you to take this time - I am having a devil of a time with my sleeves. I'll work on this throughout the week.

Vielen dank!

posaune

  • Moderator
  • Senior Member
  • *****
  • Posts: 256
  • Human Being
Re: drafting a sleeve
« Reply #18 on: August 28, 2017, 06:48:30 PM »
I'm very interested how you will find the draft.
A last end (hehehe)

Here are 3 other types of sleeves derived of the system
First is a two piece sleeve. Derived from the narrow sleeve. You set a curve on both seams about 1 cm. This way you can get more room for the biceps.
The second is a sleeve for a knitted fabric and the third is a shirt sleeve. (We had now 83% 75% and 65%)
The last two are derived from different cap heights. The shirt sleeve is already shortened for the cuff.  I have taken the same armhole dates which would not be the case in reality.
lg
posaune



Schneiderfrei

  • Research
  • Senior Member
  • ****
  • Posts: 388
  • Resembles Human Being
Re: drafting a sleeve
« Reply #19 on: August 28, 2017, 10:20:07 PM »
I am determined to do it but I am putting aside time to read through He he. :)

posaune

  • Moderator
  • Senior Member
  • *****
  • Posts: 256
  • Human Being
Re: drafting a sleeve
« Reply #20 on: August 29, 2017, 12:03:25 AM »
Oh it came out a bit long, didn't it??
lg
posaune ;D ;D

spookietoo

  • Regular Member
  • **
  • Posts: 58
  • Home Sewist - Focusing on Tailoring TN - U.S.A.
Re: drafting a sleeve
« Reply #21 on: August 29, 2017, 12:46:09 PM »
More than a bit....but then that's what I needed...lots of diagrams, directions and explanations.
 :D :D :D

I've so much going on in my life at the moment....I keep waiting for my sewing to be relaxing - I need it to be!


But then it just occurred  to me during this post, that when I am extra stressed - my brain has trouble with simple math functions....usually I'm a bit of a whiz.  Its no wonder I'm having such a problem!


So now that you've helped me realize that issue also - thank you! - hopefully I can get down to business now that I know what to do. :)

Schneiderfrei

  • Research
  • Senior Member
  • ****
  • Posts: 388
  • Resembles Human Being
Re: drafting a sleeve
« Reply #22 on: August 29, 2017, 02:53:08 PM »
By no means too long - I love it -  it does deserve the time to put in to read it. 

peterle

  • Senior Member
  • ****
  • Posts: 255
  • Experienced Professional
Re: drafting a sleeve
« Reply #23 on: August 29, 2017, 07:23:37 PM »
Oh no, it´s not too long.
It´s as long as it has to be. Thanks a lot for taking the time to write it!